NanoTag Activity Measuring Device
Wireless Temperature and Activity Measurement
|56747||NanoTag for Mice and Rats (20/pk)- requires 56745S and 56748||Login|
|56746||NanoTag for Mice and Rats (10/pk)- requires 56745S and 56748||Login|
|56745||NanoTag for Mice and Rats (5/pk) - requires 56745S and 56748||Login|
|56745S||NanoTag Viewer Software||Login|
|56748||Contactless RFID card reader/writer "PaSoRi" (cable)||Login|
|56749||Contactless RFID card reader/writer "PaSoRi" (stick)||Login|
|56745D||NanoTag for Mice and Rats Demo Set with Software||Login|
Continuous monitoring of activity and temperature up to 60 days!
Record from multiple animals simultaneously
Animals can be implanted with a nano tag® device and activity and temperature data can be collected from all of them at the same time.
Continuously record for up to 60 days*
The nano tag® internal battery will last for up to 2 months. Data can be recorded not only continuously but also intermittently for 60 days by turning on/off the power externally. Additionally, “timer stop mode” enables you to set up the device so that it will start/stop recording automatically at designated times.
* The battery life (60 days) is based on 24-hour measurement with a single 2 min/day communication for retrieval of data. Battery life is dependent on a number of factors pertaining to use.
Recorded data are stored in the nano tag® device. Stored data is retrieved into your PC by FeliCa® communication. A simple, light touch of the RFID card reader/writer(PaSoRi®) on the nano tag®, can be used to start/stop data recording. Recorded data is retrieved while the nano tag® is implanted in animal body*.
Small and Lightweight
The nano tag® is smaller than a dime (17.9mm dia.) and weights only 2g (including the battery). To make it lightweight and waterproof, nano tag® is a single-use device or disposable. The battery is unreplaceable.
Activity measuring method
Activity is defined as Cross Count Data.
[ Cross Count ]
Counts the number of times XYZ acceleration vector synthesized waveform crosses the threshold levels from bottom to top per Recording Interval(Cross Count).
The following 3 modes are available.
- “Loop mode” – Overwrite existing data from the beginning when the memory becomes full
- “Memory – full stop mode” – Data is stored sequentially until the memory becomes full
- “Timer start/stop mode” – Start/stop at designated times
nano tag® Viewer Software “nanotag/Viewer”
The nanotag/Viewer enables you to change the setting, retrieve data, make a graph, and output to a CSV data file.
- Change settings of nano tag®
- Control start/stop of data acquisition
- Retrieve data, Reset
- Make graphs
- Output to CSV data files
nano tag® viewer software
This software is necessary to use nano tag®
|Detection method||Three-axis accelerometer, Temperature sensor|
|Communication system||Near Field Communication (FeliCa® system)|
|Communication distance||Approximately 10mm|
|Time accuracy||±60 seconds / month|
|Internal battery||CR1220 (unreplaceable)|
|Battery life||Approximately 2 months (under 24-hour measurement with a single 2 min/day communication for retrieval of data using FeliCa®)|
|Recording mode||1. Loop mode
2. Memory - full stop mode
3. Timer start/stop mode
|Activity data||Cross Count|
|Temperature||10 - 45.875℃
Measurable temperature range : 15.875℃
(Resolution : 0.0625℃ Accuracy : ±0.5℃)
|Waterproof||Equivalent to IPX7 ( IEC529)|
|Size||15 X 14.2 X 7.1 mm|
Sensor: 3-axes Accelerometer
Time Accuracy: Monthly difference +/- 60sec
Battery Life: 60 days
Measurement mode: Loop, Memory-Full Stop, Timer